[Q71-Q95] PASS 300-110 exam with Cisco Real Exam Questions – 100% Valid!

NEW QUESTION 71
Refer to the exhibit. A wireless engineer is using the Ekahau Site Survey tool to conduct a post-deployment survey. The engineer analyzes the pictured output to determine if SNR meets the voice requirements. How is the voice support based on the output?
Exhibit – Q15: Ekahau SNR Heatmap – Post-Deployment Survey Output

It works in the top-middle room.

It is not supported.

It works in the lobby.

It works in all locations.

NEW QUESTION 72
A customer has three data centers and wants to deploy 1500 APs with controller redundancy that does not require a dedicated standby controller for each active controller. Which redundancy model should the engineer design?

SSO high availability with AP and client stateful switchover

N+1 redundancy using primary, secondary, and tertiary controller configuration

AP SSO with back-to-back redundancy ports

Mobility anchor redundancy

NEW QUESTION 73
A customer has multiple WLCs running in N+1 redundancy with APs load balanced between the WLCs. The customer performs AP failover testing between the WLCs and notices that some of the APs do not move back to their primary WLC after it recovers. What are two points that must be addressed in the design? (Choose two.)

DHCP Option 43 information is incorrect.

APs do not have their secondary WLC information configured correctly.

AP Fallback is not enabled on one of the WLCs.

APs do not have their primary WLC information configured correctly.

APs failover priorities are set to Low.

NEW QUESTION 74
A customer has a single anchor WLC named Anchor A.
Anchor A is in a DMZ and provides guest access. The customer wants to deploy an additional anchor controller named Anchor B to provide redundancy if Anchor A fails. Which design approach should be taken for the guest WLAN priority on the foreign WLC for each anchor WLC?

Set Anchor A to priority 3 and Anchor B to priority 3.

Set Anchor A to priority 3 and Anchor B to priority 1.

Set Anchor A to priority 1 and Anchor B to priority 1.

Set Anchor A to priority 1 and Anchor B to priority 3.

NEW QUESTION 75
An engineer is designing a solution where guests terminate on an anchor controller in the DMZ.
The engineer is having issues and wants to test connectivity between members of a mobility group. Which two steps must be performed to test whether a mobility control packet can be reached over the management interface? (Choose two.)

Use the mping command on both WLCs.

Use the eping command on both WLCs.

Open UDP port 16666 between both WLCs.

Open IP protocol 97 between both WLCs.

Use the tracert command on the WLC.

NEW QUESTION 76
What happens to an AP when a flex profile name is changed in a site tag?

It automatically updates its firmware without causing any downtime.

It temporarily disables all the currently broadcasting SSIDs.

It switches to a backup controller without any interruption.

It is forced to rejoin the controller by disconnecting the DTLS session.

NEW QUESTION 77
An engineer must identify the network requirements for a company that has a main office and 10 branch offices. The network must be able to support data, voice, video, and location tracking.
Which two factors must be considered? (Choose two.)

security policy of the company for building access

number of wireless devices that require access

type of site for which the survey will be performed

business type of the company

available power sockets in the IT room

NEW QUESTION 78
A consulting engineer is preparing to survey a brownfield deployment for a 6000-sqft building with four floors that have APs. The entire building is being remodeled and the furniture, office walls, and decoration are being updated. The engineer must perform a survey analysis on the potential RF impact of newer furniture materials. How must the survey be conducted?

Perform a sweep analysis first to predict the signal strength across each point in a floor.

Evaluate the neighbor APs strength and density based on the radio statistics information of each AP.

Measure upstream and downstream data rates based on the remodeling of the building.

Use a survey tool with the existing AP positions using building floor maps and material configuration.

NEW QUESTION 79
A customer requires the wireless network to perform real-time analysis to reduce congestion, link usage, and infrastructure upgrades. Which Cisco technology can accomplish this analysis?

band selection

QoS

Application Visibility and Control

802.11r

NEW QUESTION 80
A wireless engineer must design a WLAN for a university that requires outdoor Wi-Fi access.
Which obstruction has the greatest effect on wireless signal propagation?

wind

rain

trees

poles

NEW QUESTION 81
An engineer is designing the access layer to support Cisco Catalyst 9130 APs with both radios operating at full capability. Which power design must be specified for the switch ports?

802.3af providing up to 15.4 W per port

802.3at providing up to 30 W per port

Cisco Inline Power providing up to 7 W per port

Local power injectors on every AP with no PoE requirement

NEW QUESTION 82
An engineer configured the optimized client roaming on Cisco WLC with an RSSI threshold of -72 dBm.
Clients report frequent disconnections. What must be configured for the AP to guide the client to a better AP?

Enable BSS transition on the SSID and optimized roaming at the radio level.

Disable coverage hole detection on the SSID and enable BSS transition on the SSID.

Enable BSS transition at the radio level and optimized roaming on the SSID.

Disable optimized roaming and enable 802.11v support on the SSID.

NEW QUESTION 83
A small customer has a legacy autonomous mode Wi-Fi deployment that provides a low-density and low- capacity service. The customer wants to update and replace this deployment with the latest Wi-Fi technology but has a fixed budget that will pay only to replace the APs. Which architectural controller deployment model suits this requirement?

embedded

unified

fabric

cloud

NEW QUESTION 84
Refer to the exhibit. A wireless engineer is using the Ekahau Site Survey tool to conduct a post- deployment survey. The engineer analyzes the pictured output to determine if SNR meets the voice requirements. How is the voice support based on the output?
Ekahau SNR Heatmap — Post-Deployment Survey Output

It works in the top-middle room.

It is not supported.

It works in the lobby.

It works in all locations.

NEW QUESTION 85
An engineer is performing a passive survey report. The coverage heat map shows the entire site with all signal levels. To see only the desired coverage, which action must the engineer take?

Change the color scheme to show the desired heat map.

Use the RSSI calibration tool to configure the receiver sensitivity.

Use the RSSI slider to set the heat map to the desired cutoff filter.

Filter the results to show the desired APs only.

NEW QUESTION 86
A customer has two Cisco WLCs configured in a SSO cluster. The wireless network supports a large warehouse. The customer purchases new iPads to replace legacy scanners. Both devices connect to a single SSID named Scanning by using WPA2 Personal. The customer wants to use a standards-based method for fast roaming on the new iPads. Which approach meets the scanner requirement and still supports the legacy scanners?

Enable FT 802.1X and set Fast Transition to Adaptive for the Scanning SSID.

Enable optimized roaming globally and enable FT 802.1X on the Scanning SSID.

Enable optimized roaming globally and enable FT PSK on the Scanning SSID.

Enable FT PSK and set Fast Transition to Adaptive for the Scanning SSID.

NEW QUESTION 87
An engineer must perform a predictive wireless survey to indicate the number of access points required. The engineer has created a new project and imported the floor plan. Which step must be taken next for accurate AP placement?

Analyze the network.

Identify the coverage area.

Place the access points.

Set the scale.

NEW QUESTION 88
An enterprise network administrator is asked to set up an experimental WLAN for a collaboration project with a local service provider. The WLAN must be anchored to a WLC in the service provider data center using legacy mobility mode. After the configurations are completed on the WLCs and the firewalls in the path, the data path mobility tunnel is failing to come up. What should be performed by the administrator to debug the issue?

Establish a Telnet connection from a local PC to the firewall on port 97.

Use the mapping command on the WLC.

Establish a Telnet connection from a local PC to the firewall on port 16666.

Use the mping command on the WLC.

NEW QUESTION 89
An enterprise network is deploying two Cisco Catalyst 9800 WLCs in a data center to ensure uninterrupted wireless services for a campus with thousands of users. The IT management requests a design that enables seamless failover without client reauthentication or loss of connectivity if one controller fails. Ease of configuration and ongoing management are high priorities. The controllers will be connected via a high-speed LAN segment, and both must support full active-passive redundancy for all managed APs. Which design approach meets the requirements?

Configure the 9800 WLCs in separate mobility groups and synchronize configurations manually.

Implement SSO with redundancy management interface and AP SSO enabled between the two controllers.

Deploy the controllers with VRRP to provide gateway redundancy and manually synchronize WLAN profiles.

Enable N+1 redundancy, assigning primary and secondary controllers to each AP, and use DHCP for failover.

NEW QUESTION 90
A retailer wants to deploy Cisco Spaces for location analytics with 5 to 7 meter accuracy. Which two AP placement design rules must be followed? (Choose two.)

Place APs only in straight rows down the center of the aisles.

Ensure a client is heard by at least three APs at -75 dBm or better.

Place APs along the perimeter and in the corners of the coverage area.

Space APs no more than 15 meters apart in all directions.

Set all APs to monitor mode.

NEW QUESTION 91
A network engineer is designing a new wireless network for a campus. The network must include optimized performance, avoid interference, availability in high-density areas, and roaming. Which two approaches must be taken? (Choose two.)

5 GHz frequency band with 20 MHz channels

2.4 GHz frequency band with 20 MHz channels

5 GHz frequency band with 80 MHz channels

2.4 GHz frequency band with 40 MHz channels

5 GHz frequency band with 40 MHz channels

NEW QUESTION 92
A customer has 10 access point licenses available on their backup Cisco WLC and their primary Cisco WLC is at full capacity. 5 access points are set to high failover priority and 7 access points are set to critical failover priority. During a failure, not all critical access points failed over to the backup Cisco WLC. Which configuration is the cause of this issue?

The high priority access point is oversubscribed.

network ap-priority is set to enable.

The critical priority access point count is oversubscribed.

network ap-priority is set to disable.

NEW QUESTION 93
A customer has an existing wireless network with a Cisco 9800 WLC high availability cluster and Cisco 9120 APs. The customer asks an engineer to perform a post wireless survey that includes a list of any non-802.11 devices on the 5 GHz band. The engineer performs the survey using an 802.11a/b/g/n/ac/ax WLAN adapter but did not use a spectrum analyzer. Which approach meets the requirements?

Export a list of 802.11b interferers using the WLC and the RF ASIC embedded in the APs.

Set the WLAN adapter to monitor mode and perform the analysis by using 802.11b.

Set the WLAN adapter to monitor mode and perform the analysis by using 802.11a.

Export a list of 802.11a interferers using the WLC and the RF ASIC embedded in the APs.

NEW QUESTION 94
An engineer must design and configure a wireless network for pervasive coverage in an oil terminal, casual web and email traffic, 5 GHz. What is the best design?

Disable all data rates below 54 Mbps and assign static power level 1 on all access points.

Keep all the data rates enabled and set the AP power assignment mode to auto.

Disable all data rates below 24 Mbps and keep the power assignment on the AP as auto.

Keep the power assignment as auto and disable 802.11n and 802.11ac MCS rate.

NEW QUESTION 95
An engineer is designing a solution where guests terminate on an anchor controller in the DMZ. The engineer is having issues and wants to test connectivity between members of a mobility group. Which two steps must be performed to test whether a mobility control packet can be reached over the management interface?
(Choose two.)