[Dec 14, 2022] Fully Updated Free Actual H3C GB0-381-ENU Exam Questions [Q81-Q97]

NEW QUESTION 81
RTA and RTB run OSPF routing protocol, and both belong to the backbone area.
Which of the following methods can be used to advertise the RTA direct route 192.168.1.0/24 to the OSPF routing domain?

NEW QUESTION 82
The advantage of the OSPF protocol hierarchy is ______.

NEW QUESTION 83
Among the following routing protocols, ________ supports VLSM, but does not support automatic route aggregation. (Choose one or more)

NEW QUESTION 84
In the network shown in the figure, the BGP route learning among the routers is normal, and the BGP route attributes all take the default values.
After the route 9.0.0.0 is imported into BGP on RTD, if the next hop of route 9.0.0.0 on RTA is to point to RTC, the following adjustment methods are feasible: ______

NEW QUESTION 85
H In OSPF protocol, when the interface network type is NBMA (Non-Broadcast Multiple Access), its default Hello interval and neighbor failure time are ______ respectively.

NEW QUESTION 86
SOA-based network architecture divides enterprise IT systems into which of the following layers? (Select one or more)

NEW QUESTION 87
In IS-IS, what is the difference between Hello messages on P2P type links and LAN type links?

NEW QUESTION 88
Two MSR routers MSR-1 and MSR-2 are interconnected through the 192.168.1.0/24 network segment.
Now it is necessary to configure the OSPF protocol on the router MSR-1 to establish the adjacency relationship with MSR-2 normally. Which of the following configurations is feasible? (Choose one or more)

NEW QUESTION 89
In IPv6 stateless address autoconfiguration, which of the following ways can PC get router RA message?

NEW QUESTION 90
In the topology shown in the figure, the correct IP addresses have been configured on RTA, RTB and RTC, and the network layer is reachable.
If OSPF neighbors need to be established between routers and routes are transmitted correctly, which of the following configurations are feasible?

NEW QUESTION 91
Which of the following descriptions about BGP Peer Group is correct?

NEW QUESTION 92
The networking is shown in the figure:
The main configuration of the router is as follows:
RouterA]
bgp 100
router-id 1.1.1.1
peer 1.1.1.2 as-number 300
network 4.4.4.4 24
network 5.5.5.5 24
network 6.6.6.6 24
RouterB]
bgp 200
router-id 2.2.2.2
peer 1.1.2.2 as-number 300
network 7.7.7.7 24
network 8.8.8.8 24
network 9.9.9.9 24
RouterC]
bgp 300
router-id 3.3.3.3
peer 1.1.1.1 as-number 100
peer 1.1.2.1 as-number 200
peer 1.1.3.2 as-number 400
RouterD]
bgp 400
router-id 4.4.4.4
peer 1.1.3.1 as-number 300
peer 1.1.3.1 route-policrt1 import
ip as-path 1 permit _200_
route-policrt1 dennode 1
if-match as-path 1
route-policrt1 permit node 2
Assuming that the IP addresses of the interfaces on the four routers have been correctly configured, if there is no problem with the link, check the BGP routing table of Router D to see which of the following BGP routes:

NEW QUESTION 93
In the topology shown in the figure, the following configurations are performed on RTA, RTB, RTC and RTD respectively:
RTA] ospf 1 router-id 1.1.1.1
RTA-ospf-1] area 0
RTA-ospf-1-area-0.0.0.0] network 192.168.1.0 0.0.0.255
RTA-ospf-1-area-0.0.0.0] network 1.1.1.1 0.0.0.0
RTB] ospf 1 router-id 2.2.2.2
RTB-ospf-1] area 0
RTB-ospf-1-area-0.0.0.0] network 192.168.1.0 0.0.0.255
RTB-ospf-1-area-0.0.0.0] network 2.2.2.2 0.0.0.0
RTB-ospf-1] area 1
RTB-ospf-1-area-0.0.0.1] network 192.168.2.0 0.0.0.255
RTC] ospf 1 router-id 3.3.3.3
RTC-ospf-1] area 1
RTC-ospf-1-area-0.0.0.1] network 192.168.2.0 0.0.0.255
RTC-ospf-1-area-0.0.0.1] network 3.3.3.3 0.0.0.0
RTC-ospf-1] area 2
RTC-ospf-1-area-0.0.0.2] network 192.168.3.0 0.0.0.255
RTD] ospf 1 router-id 4.4.4.4
RTD-ospf-1] area 2
RTD-ospf-1-area-0.0.0.2] network 192.168.3.0 0.0.0.255
RTD-ospf-1-area-0.0.0.2] network 4.4.4.4 0.0.0.0
Then the routes that can be learned on RTA are _____

NEW QUESTION 94
In the topology shown in the figure, execute the following command on the RTA router:
RTA-ospf-1] default-route-advertise alwa
RTA] ip route-static 0.0.0.0 0.0.0.0 192.168.0.2
The default route cannot be observed in the routing table of the RTC router, the possible reason is ______

NEW QUESTION 95
Which of the following statements is true about filter-polic filtering OSPF routes?

NEW QUESTION 96
As shown in the figure, the MSR router at the headquarters is connected to the branch through two 100Mbps Ethernet links. To make full use of the existing bandwidth resources, which of the following routing schemes is the best?

NEW QUESTION 97
The topology of a certain network is complex, and there are multiple paths between the core and the branch. In order to control the routing between the core and the branch, effectively use the bandwidth resources, and reduce the maintenance cost, which of the following measures is optimal?