2022 Valid PD1-001 Real Exam Questions (Updated) 100% Dumps & Practice Exam [Q370-Q387]

NO.370 Which of the following is used to adjust the exposure on a scanner?

Image processor

The mirror

The scanner speed

Exposure lamp voltage

NO.371 Which of the following would result in having no dial tone? (Select THREE).

Faulty Fax/Modem Card

Telephone line unplugged

Toner cartridge empty in fax unit

RJ-11 line plugged into a digital outlet

Fax or Multi-Function unit turned off

Faulty HVPS

NO.372 A customer recently purchased a MFD and would like to setup scan using their SMTP server.
Which of the following type of scanning would be configured for the customer?

Scan-to-folder

Scan-to-FTP

Scan-to-email

TWAIN scanning

NO.373 Which of the following components can be used to write the latent image to the photoconductor?
(Select TWO).

Charge roller

Transfer unit

Development unit

Laser unit

LED array

NO.374 Which of the following electrical components detects a change of state by blocking the infrared beam with a flag or actuator?

Reflector sensor

Magnetic switch

Toggle switch

Interrupt sensor

NO.375 Which of the following functions is controlled by the printer device firmware?

Fuser temperature

Low Voltage Power Supply (LVPS)

110 volt or 220 volt operation

Switch actuation

NO.376 Toner is fused/fixed to the media by the use of:

a charge roller.

a transfer roller.

heat and pressure.

electrostatic charges.

NO.377 Adding more memory to a printer will:

extend the life of the printer consumables.

increase the load on the network when printing.

decrease the number of paper jams.

decrease the print job start time.

NO.378 A technician is onsite working on an MFD and calls technical support for assistance. The technical support asks the technician for the device details. Which of the following would be the BEST response?

Reply with the units asset tag number, model and a description of the failure.

Reply that it is some sort of printer or scanner on a shelf in the clients mail room.

Reply that the fax is not working and that you need help to get it running again.

Reply with the manufacturers name, model number and serial number.

NO.379 The transfer belt or transfer roller is supplied by which of the fol owing?

USB

HVPS

SCSI

LVPS

NO.380 Which of the following components would typically move a diverter gate?

Stepper motor

Solenoid

Relay

AC motor

NO.381 Which of the following BEST describes the purpose of firmware?

It is used as the operating system of a device.

It is used to improve print speed of a device.

It is used to configure a device via a network.

It is used to confirm connectivity of a device on a network.

NO.382 A networked multifunction device is not able to scan to email through their ISP but is able to receive print jobs from the local network. Which of the following is the issue?

Defective driver

No gateway address

Defective device network port

Duplicate IP address

NO.383 Which of the following is usually associated with a PPD?

TCP/IP

PJL

Postscript

PCL

NO.384 Which of the following steps occurs immediately after the writing process?

Charging

Fusing

Developing

Transfer

NO.385 Which of the following is the purpose of a torque limiter in a roller?

To reduce wear and tear on rollers.

To provide resistance but still allow some slippage.

To limit the amount of movement by media.

To make it easier to replace rollers.

NO.386 Which of the fol owing components can be used to remove residual charge from the photoconductor prior to charging? (Select TWO).

Charge roller

Cleaning blade

Erase LEDs

Fuser unit

Developer unit

NO.387 A client is printing a document they have received from one of their vendors on a LAN printing device. The document prints in landscape even though the printer is hard set to portrait mode and other documents print portrait. Which of the following could be the problem?

The print queue is set to landscape as default.

The page setup associated with the document in the application is set to landscape.

The print driver on their system is defaulting to landscape mode for that particular application.

The printers local defaults are set to landscape mode.

2022 Valid PD1-001 Real Exam Questions (Updated) 100% Dumps & Practice Exam [Q370-Q387]

Be the first to reply

Leave a Reply Cancel reply