[Jul-2026] EMC D-PSC-MN-01 Dumps – Reduce Your Chance of Failure in D-PSC-MN-01 Exam [Q23-Q43]

Rate this post

[Jul-2026] EMC D-PSC-MN-01 Dumps – Reduce Your Chance of Failure in D-PSC-MN-01 Exam

To help you achieve your ultimate goal, we suggest the actual EMC D-PSC-MN-01 dumps for your Dell PowerScale Maintenance Exam exam preparation to use as your guideline.

QUESTION 23
What is the role of the SolVe tool in PowerScale installations?

It provides interactive installation guides.

It monitors the installation process.

It verifies network configurations.

It assists in hardware diagnostics.

QUESTION 24
A platform engineer plans to set up a rack system for a Dell PowerScale cluster installation.
What is a requirement for the initial setup?

The rack system must have twelve independent 200-240 V power sources.

Power cords must be connected to four power distribution units within the rack cabinet.

The rack cabinet must have at least dual power supplies with power distribution.

Grounding lugs must be used for internal grounding within the chassis.

QUESTION 25
Which slot on the R640 hardware is used for front-end connectivity on a Dell EMC PowerScale F600 node?

PCIe Slot 3

rNDC Slot

PCIe Slot 1

PCIe Slot 2

QUESTION 26
What are the steps required before replacing an FRU node component?

Create a service request with Dell Support, gather logs, obtain replacement part then install

Run the isi_healthcheck command, confirm service tag, remove node cabling, extend node

Set-up workspace with ESD mat, confirm service tag, SSH into different node, run the isi healthcheck command

SmartFail node, gather logs, shut the node down

QUESTION 27
In the context of PowerScale hardware installation, why is it essential to verify the firmware version of each node?

To confirm that all nodes will operate at the same performance level

To ensure compatibility with the cluster’s existing nodes

To facilitate integration with third-party applications

To comply with data security regulations

QUESTION 28
An engineer runs ini_reformat_node command.
What are they attempting to do?

Reformat the mirrored FEC data.

Reformat a node quickly to repurpose a node.

Reformat the mirrored journals.

Reformat a node to securely erase all data.

QUESTION 29
A customer has purchased a new Dell PowerScale cluster consisting of eight F600 nodes and four H5600 nodes.
What is required when installing these nodes?

Deep rack for the H5600 chassis

Step-up transformers for the H5600 nodes

At least one standard 40U-P rack

An additional 1U of space for cable management

QUESTION 30
What is a key step when connecting nodes to the data center’s power supply during a PowerScale installation?

Using power cables of the shortest possible length to reduce resistance

Ensuring each node is connected to a different circuit breaker

Implementing power redundancy for each node

Labeling power cables according to the nodes they supply

QUESTION 31
A platform engineer is at a customer site to replace a failed Dell EMC PowerScale Gen 6 node. After removing the compute module, they observe lit LEDs inside the removed node.
What is the recommended response?

This is not normal; they need to shut down the partner node.

There is an internal electrical fault; they should call support.

The node is not yet completely shut down; they should wait.

This is normal; they should continue with the procedure.

QUESTION 32
The SSD has failed in a Dell EMC PowerScale H400 node that has one SSD installed. A technician is asked to replace it.
Where should the new drive be installed?

Left slot at the back of the node

Position 0 and sled A

Position 0 and sled E

Right slot at the back of the node

QUESTION 33
When configuring internal networking for a PowerScale cluster, what is a critical requirement?

Ensuring all nodes are in the same subnet

Implementing redundant switch configurations

Using IPv6 addressing

Setting up VLAN tagging

QUESTION 34
Which of the following are critical steps when replacing a PowerScale node’s motherboard? (Select two)

Updating the node’s firmware to the latest version

Configuring the BIOS settings according to cluster requirements

Performing a full system backup

Verifying network port configurations

QUESTION 35
A Dell PowerScale Gen 6 chassis is being installed. The chassis has been aligned with the rails.
What is the correct order of steps to finish the installation?

1. Push the node off the lift arms and into the rack.
2. Release the lift casters and carefully slide the chassis into the cabinet as far as the lift allows.
3. Install two mounting screws at the top and bottom of each rail to secure the chassis to the rack.
4. Slide the first few inches of the back of the chassis onto the supporting ledge of the rails.
5. Secure the lift casters on the floor.

1. Release the lift casters and carefully slide the chassis into the cabinet as far as the lift allows.
2. Push the node off the lift arms and into the rack.
3. Install two mounting screws at the top and bottom of each rail to secure the chassis to the rack.
4. Slide the first few inches of the back of the chassis onto the supporting ledge of the rails.
5. Secure the lift casters on the floor.

1. Install two mounting screws at the top and bottom of each rail to secure the chassis to the rack.
2. Release the lift casters and carefully slide the chassis into the cabinet as far as the lift allows.
3. Secure the lift casters on the floor.
4. Slide the first few inches of the back of the chassis onto the supporting ledge of the rails.
5. Push the node off the lift arms and into the rack.

1. Secure the lift casters on the floor.
2. Slide the first few inches of the back of the chassis onto the supporting ledge of the rails.
3. Release the lift casters and carefully slide the chassis into the cabinet as far as the lift allows.
4. Push the node off the lift arms and into the rack.
5. Install two mounting screws at the top and bottom of each rail to secure the chassis to the rack.

QUESTION 36
Refer to the exhibit, which shows the rear of the Dell EMC PowerScale Gen 6 node.

What is the function of the item associated with Callout 4?

Back-end and front-end Ethernet connectivity

Back-end InfiniBand and Ethernet connectivity

Front-end Ethernet connectivity

Back-end InfiniBand or Ethernet connectivity

QUESTION 37
A node has been removed from a Dell PowerScale cluster running OneFS 9.0.
Which PowerScale feature redistributes data across the remaining nodes?

SyncIQ

Smartpool

SmartProtect

SmartFail

QUESTION 38
What type of upgrade on a Dell PowerScale cluster requires the least amount of time?

Simultaneous

Parallel

Rolling

Automatic

QUESTION 39
What is a fundamental step in creating a new PowerScale cluster?

Selecting a cluster name and assigning it an IP range

Installing anti-virus software on all nodes

Configuring email alerts for system warnings

Subscribing to a support plan for hardware replacement

QUESTION 40
Which Dell EMC PowerScale Gen 6 components are considered CRUs?

SSD, power supply, fan, and bezel

Back-end switch, power supply, disk drive, and bezel

SSD, power supply, disk drive, and bezel

SSD, memory card, disk drive, and bezel

QUESTION 41
Refer to the exhibit.

A platform engineer has connected power cables to a Dell EMC PowerScale.

Warning event

On and healthy

Cold and redundant

Not functioning

QUESTION 42
A platform engineer is cabling a large Dell PowerScale cluster of 24 H600 nodes using the Leaf- Spine topology for the back-end network.
What is a characteristic of this topology?

Cluster nodes connect to spine switches, which communicate with each other via leaf switches

Cluster nodes connect to leaf switches, which communicate with each other via spine switches

All spine switches are interconnected

All leaf switches are interconnected

QUESTION 43
A platform engineer is installing a Dell EMC PowerScale cluster with 12 F200 nodes.
What is the correct ratio used for the breakout cable?

1:2

1:4

1:8

1:10

Accurate & Verified Answers As Seen in the Real Exam here: https://www.actualtorrent.com/D-PSC-MN-01-questions-answers.html

[Jul-2026] EMC D-PSC-MN-01 Dumps – Reduce Your Chance of Failure in D-PSC-MN-01 Exam [Q23-Q43]

Be the first to reply

Leave a Reply Cancel reply